Urc-r6 universal remote manual

Previous Page. Next Page. Universal remote automator urc owners manual 56 pages. This document is protected by the copyright laws of the United States and internationally by the Berne Convention. This prevents battery power from being depleted should the remote accidentally slip between the couch cushions. One of these will work for you!

The codes are listed by component category i. For instance, if you would like to locate a code for a Sony television, first locate the TV category and then look for the Sony brand. Use the Number buttons 0—9 on the remote to punch in the code. The remote will exit the programming mode and you will have to start over. Each time the UP Make sure the heads are one to two inches apart.

Pressing any one of the Macro buttons, or Automated activity, will send out the series of commands that are stored in that particular button. If you do not press a button within 30 seconds, the component LED light will turn off.

Each press adds a one-half second delay. Each button will access one of your favorite channels with just one button press. Each button can pro- gram up to 5 favorite channels or a total of 20 button presses , but you're not limited to using these buttons for only that.

The Component LED light will blink three times to confirm that it is saved. STEP 1: Press and hold the component button you want to add channel control to, such as Because most TVs have a "Toggle" input feature, there's no way to jump to a spe- cific video source discretely.

Page Erasing Commands-Overview Erasing Commands -- Overview You can erase a single learned command, all learned commands in each component mode, SimpleSound programming, MacroPower commands, or re--set the remote to original factory default settings. For example, if you want to erase all learned commands on the TV component button because you bought a new TV, the process is very simple. All programming and set-up codes that you have entered into the remote will be erased and the AVEX R6 will return to the original factory default settings.

Here is a way for you to identify what that code number is, so you can make a note in the back of this Manual for future reference. Some brands have more than one three-digit code. Displays information about the program currently playing or highlighted in the Program Guide through the Cable Set Top Box. Silences the Audio. Press to activate. Press again to restore sound to the previous level. Use to enter code numbers for programming components and to enter channel numbers to tune in channels.

Also used to make numeric entries on on-screen menus. There are three different ways you can program your AVEX R6 using the component brand codes that are pre-programmed into the remote. One of these will work for you! While holding down the component button, begin to press numeric. STEP 3: Release the component button to save the code. The component LED light will blink three times to confirm that the code has been stored. STEP 1: Find the 3-digit code numbers assigned to your brand from the lists in the back of this manual.

The codes are listed by component category i. For instance, if you would like to locate a code for a Sony television, first locate the TV category and then look for the Sony brand. This signals that you are in programming mode. If you do not press a button within 30 seconds,the component LED light will turn off. The remote will exit the programming mode and you will have to start over. Use the Number buttons 0—9 on the remote to punch in the code. If the 3-digit code number you just punched in is the correct number, the component you are trying to program will turn off.

If it did not turn off, enter the next code number from your list until it does turn off. For example, perhaps your Sony TV turned off with code number , but the volume controls did not work properly. In this case, try the next code number listed for that component. Repeat Step 5 using the next code number until you find a perfect match. Press the component button you just programmed in this case TV one more time to save the code number.

The component LED light will blink three times to confirm that the code was successfully stored. Now when you press the TV component button, all of the buttons will work with your TV. The Auto-Search Method is a way you can scan through all of the codes in the table to find the right code for your component. Hold down both buttons for 2 seconds until the TV Component button light turns on. If you do not press a button within 30 seconds, the component LED light will turn off.

When the correct code is sent out, the component will turn off. If any of the buttons do not work properly, you need to find a new code. STEP 5: Once you have found the right code, you must save it. Now you can continue learning all other buttons from your old remote by pressing the next button on the AVEX R6 and repeating this step. Note: The component LED will blink five times if there was an error in the learning process. In this case, please repeat Steps 3 and 4.

The component LED light will blink three times to confirm the programming. Now test all the buttons to make sure they learned correctly. Pressing any one of the Macro buttons, or Automated activity, will send out the series of commands that are stored in that particular button. MacroPower makes several devices work together by pressing one button. What could normally take three remotes and three button pushes, the AVEX R6 can accomplish with the press of one button.